Brief Introduction

IV2-G30F

ModelIV2-G30FTypeLearning/standard typeToolsAvailable modesLearning mode / Standard modeStandard mode built-in toolsOutline, Color area*1, Area*2, Edge pixels, Color average*1, Brightness average*2, Width, Diameter, Edge presence, Pitch, OCR, Color/brightness prohibit, Position adjustment, High-speed position adjustment (1-axis edge/2-axis edge)Number of toolsDetection tools: 16 tools, position adjustment tool: 1 tool*3Switch settings (programs)128 programs (when using SD card) / 32 programs (when not using SD card)IndicatorsPWR/ERR, OUT, TRIG, STATUS, LINK/ACT, SDImage historyNumber of storable images1000 images *4Save conditionsSelectable between NG only, NG and OK near threshold*5, and All *4Image data transferTransfer destinationSelectable between SD card and FTP serverTransfer formatSelectable between bmp, jpeg, iv2p, and txtTransfer conditionsSelectable between NG only, NG and OK near threshold*5, and AllAnalysis informationRUN displayTools list (Judgment results, degree of similarity, or degree of similarity bar display) *6RUN informationSwitchable between OFF, histogram, processing time, count, and output monitorHistograms: Histogram, degree of similarity (Max., Min., Ave.), Number of OKs, Number of NGsProcessing time: Processing time (latest, Max., Min., Ave.), Image capture interval (latest, Max., Min., Ave.)Count: Trigger numbers, Number of OKs, Number of NGs, Trigger errors, Strobe errorsOutput monitor: ON/OFF status by outputOther functionsImage capture functionImage buffer, Image capture range, Digital zoom (2×, 4×), HDR, High gain, Color filter*1, White balance*1, Brightness correctionTool functionsLearning mode: Additional learningStandard mode: Mask outline, Masking function, Color extraction/exclusion*1, Color histogram function*1, Monochrome histogram function*2, Scaling functionUtilitiesFailing sensor list, Failure hold, Test run, I/O monitor, Security settings, Simulator*7InputTypeSwitchable between non-voltage input and voltage inputFor non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit)For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.2 mA or lower, ON current 2 mA (for 24 V)Number of inputs8 (IN1 to IN8)FunctionIN1: External trigger, IN2 to IN8: Enable by assigning optional functionsAssignable functions: Program switching, Clear error, External master image registration, SD card save cancelOutputTypeOpen collector output; NPN/PNP switchable, N.O./N.C. switchableFor open collector NPN output: Maximum rating of 26.4 V, 50 mA, residual voltage of 1.5 V or lessFor open collector PNP output: Maximum rating of 26.4 V, 50 mA, residual voltage of 2 V or lessNumber of outputs8 (OUT1 to OUT8)FunctionEnable by assigning optional functionsAssignable functions: Total judgment (OK/NG), Run, Busy, Ready, Strobe, Position adjustment result, Judgment result of each tool, Result of the logical operation of each tool, Error, SD card errorEthernetStandard100BASE-TX/10BASE-TConnectorRJ45 8-pin connectorNetwork functionFTP client, SNTP clientInterface compatibilityBuilt-in EthernetEtherNet/IPⓇ, PROFINET, TCP/IP non-procedure communicationCommunication unitEtherCATⓇ, CC-Link, DeviceNetⓇ, PROFIBUS, RS-232C*8Expanded memorySD card (SD/SDHC) *9RatingPower voltage24 VDC ±10% (including ripple)Current consumption1.8 A or less (including communication unit and output load)Environmental resistanceAmbient temperature0 to +50°C 32 to 122°F (No freezing)Relative humidity35 to 85% RH (No condensation)MaterialMain unit case: PC, Power connector: PA/POM, I/O connector: PA, Sensor head connector: Zinc + Ni plating/PA,Ethernet connector: Copper alloy + Ni plating, Main unit rear heat sink: Aluminum, Main unit rear DIN rail fixing tab: POM, Nameplate: PCWeightApprox. 330 g*1 Color type only.*2 Monochrome type only.*3 Tools can be installed by programs.*4 Saves to the sensor amplifier’s internal memory. The images saved to the sensor amplifier can be backed up to a USB memory stick inserted into the control panel (IV2-CP50) or to the PC where the software for the IV2 Series (IV2-H1) is being used.*5 Learning mode only.*6 Can also be displayed on the control panel (IV2-CP50) or the software for the IV2 Series (IV2-H1).*7 Usable on the software for the IV2 Series (IV2-H1).*8 When a communication unit (DL Series) is connected.*9 Use only products recommended by KEYENCE.